LUNT Blue-Glass 20mm for B400 to B1800 blocking-filters

Spare part for Pressure-Tuner of MT and THa series H-alpha solar telescopes from LUNT SOLAR SYSTEMSTwo rubber O-rings are installed into the Pressure-Tuner of Lunt Solar Systems solar telescopes to seal the air-pressure tuning system. Over time, the rubber of this O-rings can age and become porous, whereby the air-pressure can then no longer be maintained. When this happens, a old O-ring can be replaced by this spare part. The replacement is simple and can be done by the user. Installation instructions can be found here under the tab "Manuals" as a PDF file for download.Please be sure to note:Depending on the production series, the diameters of the Pressure-Tuner pistons can vary slightly. There are pistons for O-rings with 32mm inner diameter and 40mm outer diameter, and pistons for O-rings with 34mm inner diameter and 42mm outer diameter. Please check the diameter of your old O-rings, this spare part is an O-ring with 34mm inner diameter and 42mm outer diameter.If you need the smaller O-ring with 32mm inner diameter and 40mm outer diameter, this is the spare part with item number 0558330.The LS50THa telescopes have Pressure-Tuners with smaller diameters, for these you will need replacement O-rings with item number 0558320.After replacing a O-ring, the piston and cylinder of the Pressure-Tuner can be re-greased with grease available under item number 0558350.FEATURESInner diameter: 34mmOuter diameter: 42mmCannot be used separately, only as a replacement part on the Pressure-Tuner of MT and THa telescopes from Lunt Solar Systems.It does not matter what blocking-filter is at the MT or THa telescope.SCOPE OF DELIVERYSpare part one O-ring with 34mm inner diameter and 42mm outer diameter for Pressure-Tuner of MT and THa H-alpha solar telescopes from Lunt Solar Systems

​Spare part for Pressure-Tuner of LS50THa H-alpha solar telescopes from LUNT SOLAR SYSTEMSA rubber O-ring is installed into the Pressure-Tuner of Lunt Solar Systems LS50THa solar telescopes to seal the air-pressure tuning system. Over time, the rubber of this O-ring can age and become porous, whereby the air-pressure can then no longer be maintained. When this happens, the old O-ring can be replaced by this spare part. The replacement is simple and can be done by the user. Installation instructions can be found here under the tab "Manuals" as a PDF for download.After replacing the O-ring, the piston and cylinder of the Pressure-Tuner can be re-greased with grease available under part number 0558350.Please note that this spare part can only be used on the Lunt Solar Systems LS50THa H-alpha solar telescopes. If the problem occurs on the larger THa or MT series telescopes, the larger O-rings with part numbers 0558330 or 0558340 must be used there.FEATURESInner-diameter: 31mmOuter-diameter: 39mmCannot be used separately, only as a replacement part on the Pressure-Tuner of the LS50THa telescopes from Lunt Solar Systems.It does not matter what blocking filter is at the LS50THaSCOPE OF DELIVERYSpare part one O-ring for pressure tuner of LS50THa

Spare part for Pressure-Tuner of MT and THa series H-alpha solar telescopes from LUNT SOLAR SYSTEMSFor example, if the O-rings have been changed on a Pressure-Tuner of a Lunt Solar Systems H-alpha solar telescope, the Pressure-Tuner can be re-greased with this grease. The grease can be applied to the piston with the O-rings and to the threads of the brass cylinder on the Pressure-Tuner. It keeps the Pressure-Tuner running smoothly and seals it.Please note:Do not use too much grease inside the brass cylinder. The grease must not get into the air passage at the bottom of the brass cylinder, otherwise the Etalon could be damaged in the worst case.FEATURESLithium grease with Teflon contentVery good sealing propertiesHigh adhesion and good corrosion protectionTemperature stable from -20 to +120° CelsiusConstant viscosity during temperature fluctuationsSCOPE OF DELIVERYSpare part: Grease for Pressure-Tuner of MT and THa H-alpha solar telescopes from Lunt Solar Systems

Spare part for Pressure-Tuner of MT and THa series H-alpha solar telescopes from LUNT SOLAR SYSTEMSTwo rubber O-rings are installed into the Pressure-Tuner of Lunt Solar Systems solar telescopes to seal the air-pressure tuning system. Over time, the rubber of this O-rings can age and become porous, whereby the air-pressure can then no longer be maintained. When this happens, a old O-ring can be replaced by this spare part. The replacement is simple and can be done by the user. Installation instructions can be found here under the tab "Manuals" as a PDF file for download.Please be sure to note:Depending on the production series, the diameters of the Pressure-Tuner pistons can vary slightly. There are pistons for O-rings with 32mm inner diameter and 40mm outer diameter, and pistons for O-rings with 34mm inner diameter and 42mm outer diameter. Please check the diameter of your old O-rings, this spare part is an O-ring with 32mm inner diameter and 40mm outer diameter.If you need the larger O-ring with 34mm inner diameter and 42mm outer diameter, this is the spare part with item number 0558340.The LS50THa telescopes have Pressure-Tuners with smaller diameters, for these you will need replacement O-rings with item number 0558320.After replacing a O-ring, the piston and cylinder of the Pressure-Tuner can be re-greased with grease available under item number 0558350.FEATURESInner diameter: 32mmOuter diameter: 40mmCannot be used separately, only as a replacement part on the Pressure-Tuner of MT and THa telescopes from Lunt Solar Systems.It does not matter what blocking-filter is at the MT or THa telescope.SCOPE OF DELIVERYSpare part one O-ring with 32mm inner diameter and 40mm outer diameter for Pressure-Tuner of MT and THa H-alpha solar telescopes from Lunt Solar Systems

Blocking-filter in 90° zenith mirror diagonal, for telescopes up to 1080mm focal length, and with 2 inch (50.8mm) focuser. Can only be used together with a LUNT H-alpha filter, or with a LUNT H-alpha telescope!Lunt Solar Systems offers blocking-filters in different sizes, and alternatively in 90° star-diagonal housings or straight extension tubes. You can choose what blocking-filter you will use at your LUNT H-alpha Etalon system.The B1200d2 is installed in a 90° star-diagonal housing, for 2 inch (50.8mm) focuser on the telescope side, and with T2 thread and 1.25 inch (31.7mm) eyepiece connection on the eyepiece side. The B1200d2 can be used at LUNT H-alpha systems, if the used telescope has a 2 inch focuser and up to 1080mm focal length.The blocking-filter can not be used without additional H-alpha filter system from Lunt Solar Systems! Blocking-filters are absolutely required for the safety and performance of H-alpha telescopes for solar observing. Lunt Solar Systems blocking-filters contain a unique filter system. We can only warranty safety or performance, if blocking-filter is paired with a H-alpha filter or H-alpha telescope of Lunt Solar Systems.At the tab ''Accessories'' you will find H-Alpha telescopes and filters with which this blocking filter can be combined.FEATURESBlocking-filter only usable at additional H-alpha filter systemFilter diameter: 12mmUsable at telescopes up to 1080mm focal90° star-diagonal housing2 inch slide tube for 2 inch focuserConnection for 1.25 inch eyepiecesT2 thread for camera connectionSCOPE OF DELIVERYBlocking-filter B1200d2 in 90° star-diagonal for 2 inch focuser

Whether in the photo or film studio, or for camping and leisure, the BRESSER BR-21 gooseneck is always a good helper for attaching photo studio accessories and other utensils. With two different clamps, the flexible arm is quickly and flexibly attached to table tops or tripos.The stable and flexible component has a total length of 43 cm and can be stowed away quickly to save space. Books, reflectors, microphones, leisure equipment and much more - there is hardly anything that the BRESSER Gooseneck cannot hold. The rubberised screw clamp with an opening of 0,5 to 3,5 cm can also be mounted on tubes and rods, microphone stands or lamp tripods. The rubberised spring clamp with its robust width of 7,5 cm has a maximum opening of 5 cm. Conveniently, the BRESSER BR-21 can also be used in reverse. The spring clamp can be used as a table clamp and screw clamp can be used as a holder for tubes, rods ect.NOTE: The load capacity of approx. 1-2 kg depends on the angle of inclination and may therefore vary.PROPERTIESFlexible bendable arm 43 cm/ Ø 15 mmTotal length: 62 cmMetal clamp with strong spring on one side, screw clamp on the other sideRemoveable rubber lipsSpring clamp opnening: max 5,5 cmClamp width: 7,5 cmTube clamp width: 4 cm/ length: 5 cmScrew clamp opening: 0,5 cm - 3,5 cmLoad capacity: max 1-2 kg, depending on angle of inclinationSCOPE OF DELIVERY1x BRESSER BR-21 Flexarm