BRESSER Extension tube 2"/35mm

BRESSER 40mm Plössl Eyepiece 1,25" (31,7mm) Since years a well known and approved Plössl eyepiece. Ideal to improve the performance of your telescopes for a low budget price. All the BRESSER Plössl eyepieces provide sharp and high-contrast images because of the 4-lens design. All lenses have fully-multicoated surfaces which prevents reflections efficiently. Every eyepiece is equipped with a foldable rubber eyecup to avoid straylight from the sides and the inner eyepiece shaft is carefully blackened as well. Housing and eyepiece shaft are completely made from metal - no plastic is used. Filter thread for use with colour- and nebular filters is also available. All these Plössl eyepieces offer a much better image quality than all the very simple made Kellner and Huygens eyepieces. FEATURES Focal length: 40 mm Field of view: 46° Lens-Design: 4 lenses in 2 groups , fully-multicoated Housing material: completely made from metal Rubber eyecup: YES, foldable Filter thread: YES Storage: Twist-pack SCOPE OF DELIVERY BRESSER Plössl eyepiece with rubber eyecup Twist-pack

The BRESSER UV + IR Cut Filter makes lunar and planetary images even sharper.Digital astro cameras have a wide sensitivity range that significantly exceeds the spectrum of visible light. Thus, the wavelengths of invisible light in the ultraviolet and infrared are also captured. This leads inevitably to a small additional and of course unwanted blur. The solution is this UV + IR Cut Filter, which allows only light in the visible range 400 nm to 680 nm to pass through and blocks all other wavelengths of light. As soon as these disturbing light waves are cut off, the sharpness of the image and the contrast are increased. Suddenly, details on the surface of Jupiter, for example, can be seen that were previously only barely visible. A clear plus, which can be achieved by this filter.Suitable for BRESSER CMOS cameras and other manufacturers with female camera thread M30 x 0.75 mmAfter removing the original screw adapter with sensor protection glass, the BRESSER UV + IR Cut filter is mounted to the camera instead. This filter has a fine M30 x 0.75 mm external thread for mounting on the camera. The exchange is therefore quick and easy. On the opposite side, i.e. on the telescope side, there is a standard C-mount female thread for mounting other accessories. Note: This filter does not have a standard 1.25 inch (31.7 mm) filter thread. FEATURESBRESSER UV + IR Cut Filter for photographyWavelengths of invisible light in ultraviolet and infrared are blockedPasses only visible light in the range 400nm to 680nmLunar and planetary images become even sharperSuitable for BRESSER CMOS cameras an othersMale fine thread M30 x 0.75mm for mounting on the camera housingC-Mount internal thread for mounting further accessories Quick and easy mounting of the filterGlass filter made of fine optical glassPlane-parallel polished and multiple layer coatedFilter housing made of matt black anodized aluminumHousing outer diameter 31.7mm (1.25 inch)Diameter of free light transmission 17.0mm (1.25 inch) SCOPE OF DELIVERYUV + IR Cut Filter (1 pc)

Sol-Searcher for installing on all solar telescopes of Lunt Solar Systems. The tube rings of the LUNT solar telescopes are prepared for the mounting of this Sol-Searcher."I can't find the Sun!" sounds funny. However, the Sun is tricky to find in a properly filtered telescope, and you don't ever want to chance a direct gaze, let alone a magnified image of it.This Sol-Searcher is the safe and easy way to find the Sun. It is absolutely safe since you don't look through Sol-Searcher, you look at it. The aperture acts as a "pinhole" which projects an image of the Sun on to the 1/4" translucent "screen." This screen can be viewed from either side. Simply move your scope until the Sun's image is centered on the screen and the Sun will be in the eyepiece's field of view.The solar telescopes from Lunt Solar Systems are fitted for installing this Sol-Searcher. Only at the LS130MT and LS152THa telescopes the additionally adapter 0554302 will be needed.SCOPE OF DELIVERYTeleVue Sol-SearcherScrewsHexagon wrench

Connect your BRESSER Microscope or Telescope with a Sony System camera and take images or videos* of your observed object!T-Mounts are the connecting piece between the T2 camera adapter and the system camera. Please read the instruction manual of your camera to find out which T-Mount you need, look into the instruction manual of your camera.The adapter will provide the necessary distance extension between the flange focal length of 18mm for E-Mount and 55mm for T2. The overall length is 37mm.For Sony NEX or ILCE cameras with E-Mount bajonet (e.g. Sony Alpha 6000, Sony A7S / A7R)SCOPE OF DELIVERYT2-Ring für Sony E-Mount camerasFor Sony NEX, ILCE Cameras (e.g. A7S, A7R)

Explore Scientific 82° Series™ extreme wide field eyepieces are optimized to produce high contrast, high resolution, and superior flat field characteristics. The visual effect of these eyepieces with their long eye-relief and their 82° apparent field is truly a full-immersion experience. Your eye is relaxed, allowing you to easily use the "averted vision" technique to study faint details across a huge field-of-view. The 82° Series eyepieces come with a twist-up rubber eye-guard that raise to the desired height for the comfort of the observer, and as experienced astronomers know, eye comfort is critical when trying to observe at the visual limits of the telescope. To keep internal reflections to a minimum, all internal surfaces of the eyepiece barrel are flat black, as well as the edges of the lenses themselves to minimize the scattering of light within the lenses themselves. All 82° Series eyepieces are fully multi-coated and edge-blackened to produce maximum contrast.

AP clamping lever for the AP mount axesThe friction control mechanism (slip clutch) can be secured in place with the AP clamping lever. FEATURES Clamping lever for use in combination with Vixen AP modules Dimensions: 23 mm x 33 mm x 31 mm Weight: 10 g DELIVERY CONTENT 1x clamping lever